- Ivi door lock troubleshooting how to#
- Ivi door lock troubleshooting driver#
- Ivi door lock troubleshooting manual#
I am also having intermittent problems with the rear barn door lock.
Ivi door lock troubleshooting how to#
They kept it for 5 days and returned it un-repaired but without any cost.Īnyone have an idea how to troubleshoot this? This problem started while at the dealer getting a winter service. I even replaced the door lock switch but it didn’t change anything.
Ivi door lock troubleshooting driver#
I tore the driver door apart and inspected all wires and found nothing apparent. I metered the fuse slot and see the top terminal is hot (12v) and the lower peg is a hard ground. It is labeled “cig liter” but the cigarette lighter works even when this fuse is unplugged. It pops immediately when a fuse is installed.
![ivi door lock troubleshooting ivi door lock troubleshooting](https://www.access-locksmiths.co.uk/wp-content/uploads/2019/12/change-lcoks-1.png)
I checked the fuse box and found #13 fuse blown. They all function automatically by locking when the truck is started and placed in gear and by unlocking when the truck is shut off. The lock/unlock switch on the driver side arm rest will not activate the door locks.īut…. My 1997 2500 Suburban has a different twist. Refer to the meters instruction for proper usage and precautions. A volt meter, available at any auto parts store, can be used to check the voltage to the individual lock solenoids and switches. PRECAUTIONS, TIPS, and NOTES An inspection of the rubber boot and wiring harness that connects from the door frame and the door can often reveal wiring damage. If a click is heard but the lock did not engage, a problem with the door lock mechanism or linkage is the most likely cause. You should listen to the affected door while energizing the door lock. If all of the door lock switches are functional but one door fails to operate, the most likely problem is an open circuit in the circuit between the switch and solenoid or a defective solenoid in the affected door. If the doors lock with any one switch the most likely problem is a defective switch on the door that is inoperative. Operate each door lock switch in the vehicle to determine if the doors can be locked with any of the switches.
Ivi door lock troubleshooting manual#
Consult the fuse box placard or your owners manual for fuse designations and ratings. Inspect the fuse that protects the door lock circuit to ensure it is not blown.
![ivi door lock troubleshooting ivi door lock troubleshooting](https://www.home-repair-central.com/images/door-lock-repair-pic2.jpg)
An inoperative power door lock can be caused by the switch, solenoid, wiring problem or mechanical problem within the linkage of the affected door.ĭIAGNOSIS If all of the door locks are inoperative, start your diagnosis at the fuse box. To unlock the doors the switch reverses the polarity of the voltage applied to the solenoid. To lock the doors the switch provides voltage to the two terminals of the solenoid. The switch provides power to the door lock solenoids. USUAL CAUSE The power door locks utilize individual solenoids in each of the doors that activate the door lock mechanism. SYMPTOM SUMMARY The power door locks are all inoperative or a single door lock is inoperative. A local Nest Pro can diagnose what’s causing the problem and fix it for you.DIAGNOSE – POWER DOOR LOCKS DON’T WORK PROPERLY If you’re having trouble with a misaligned lock, you don’t have to figure it out on your own.
![ivi door lock troubleshooting ivi door lock troubleshooting](https://torontodoorframes.ca/wp-content/uploads/2017/07/sliding-door-lock.jpg)
If there’s any friction, or if you need to push or pull on the door to get the lock to fully engage, it’s a good sign your deadbolt is misaligned.
![ivi door lock troubleshooting ivi door lock troubleshooting](https://i.ytimg.com/vi/0CK8PZnnDIQ/maxresdefault.jpg)
Gently close your door and use the thumb turn inside your home to lock it.Over time, the deadbolt may acquire a build-up of dirt, dust, or other material that slightly changes its size enough to prevent it from perfectly aligning with the strike plate any more. This can cause just enough misalignment to prevent the lock from being able to work on its own any more. If the deadbolt on your door isn’t perfectly aligned with the strike plate on your doorframe, your lock may not be able to lock itself.Įven if you installed the lock perfectly when you first got it, the door and the frame can shift over time, or they can shrink and swell in different weather conditions.